XL2 305 Ø32mm 4-hole 106.4
Danfoss XL2 Series – High-Torque Orbital Motors with Disc Valve Design
The Danfoss XL2 series belongs to the Xcel™ family of low-speed, high-torque orbital motors and is designed for medium-duty mobile and industrial applications requiring reliable torque output and long service life.
Built on a disc-valve system with a three-zone design, the XL2 delivers smooth operation, high efficiency, and stable performance under varying loads. Precision-engineered bearings and optimized porting ensure consistent torque and extended durability in a compact design.
Each motor in the XL2 range features a SAE A 2-bolt mounting flange, G-thread ports, and a robust steel housing engineered to meet demanding system requirements.
Key Advantages
- High efficiency and torque stability at low speeds
- Three-zone disc-valve design for extended life and true bi-directionality
- Hydrodynamic bearings ensure smooth, reliable operation
- Compact and durable construction for medium-duty applications
- Optional cross-over relief or counterbalance valves for flexible system design
- Displacement range: 80 – 490 cm³/rev
- Continuous pressure: up to 205 bar
Intermittent pressure: up to 310 bar
Continuous torque: up to 845 Nm
Intermittent torque: up to 930 Nm
Speed capability: up to 900 rpm (depending on model)
Typical Applications
• Augers and screw conveyors
• Sweepers and snow blowers
• Conveyors and material-handling systems
• Agricultural and municipal equipment
• Compact drives and auxiliary hydraulic mechanisms
Technical Highlights
• Displacement range: 80 – 490 cm³/rev
• Flow capacity: up to 75 l/min continuous / 115 l/min intermittent
• Torque range: up to 845 Nm continuous / 930 Nm intermittent
• Operating temperature: –34 °C to +82 °C
• Recommended oil: Premium anti-wear hydraulic oil, viscosity ≥ 13 cSt at operating temperature
• Filtration: ISO 4406 class 20/18/13
• Ports: G ½ (pressure) / G ¼ (drain)
• Mounting flange: SAE A 2-bolt (Ø 82.5 mm pilot / Ø 106.4 mm bolt circle)
• Shaft options: Ø 32 mm cylindrical (code 16) or Ø 31.75 mm 14-tooth spline (code 99)
• Shaft seal: Standard pressure type (high-pressure optional)
• Maximum inlet pressure: 310 bar [4500 psi]
Note
Motors can run continuously at listed ratings; intermittent operation should not exceed 10 % of each minute.
For maximum service life, pre-run the motor at approximately 30 % of rated pressure for one hour before full-load operation.
Connecting a case drain line is recommended when operating at high pressures or temperatures to maintain low case pressure and extend seal life.
Varenummer:
629AG00721A
Pakke str.:
0 pcs
Min. bestillingsenhed er:
1 pcs
Aksel diameter
32 mm
Akseltype
Cyl. Ø 32 mm
Akseltætningstype
Standard shaft seal
Antal montage huller
4
Arbejdsporte
G 1/2 BSP
Boltcirkel
106.4 mm
Dimension X
175.1 mm
Dimension XX
135 mm
Dimension Y
222.3 mm
Dimension YY
182.4 mm
Drænport
G 1/4 BSP
Filtreringskrav
ISO cleanliness code 4406:20/18/13
Flangens Styrediameter
82.5 mm
Fortrængning
305 cm3
Forureningsgrad maks.
20/18/13 - ISO 4406
Indgangstryk Maks.
310 bar
Integreret Kontraventil
No
Intermittent Flow Maks.
115
Intermittent Moment Maks.
885 Nm
Intermittent Rotationshastighed Maks.
365
Kontinuerligt Flow Maks.
75
Krav til drænledning
Recommended (Required under high case pressure)
Længde
222.3 mm
Maks. driftstemperatur
82 °C
Maks. moment på aksel
768 Nm
Maling
Black
Model kode
XL2
Moment kontinuerlig maks.
765 Nm
Monteringsflange
SAE-A4
Mærke navn
Danfoss
Olieviskositet anbefalet
20 - 75 cSt
Portkode
AS
Portplacering
Side
Reces
82,55 mm
Rotationshastighed kontinuerligt maks.
246 rpm
Temperatur maks.
+180 °C
Temperatur min.
-30 °C
Tryk intermitterende maks.
240 bar
Tryk kontinuerligt maks.
205 bar
Förpackningsstorlek
0 pcs
Streckkod
5704334982814
Bruttovikt
Kg
Nettovikt
Kg
Ursprungsland
CHN
Intrastat artikelkod
84122981
Danfoss XL2 Series – High-Torque Orbital Motors with Disc Valve Design
The Danfoss XL2 series belongs to the Xcel™ family of low-speed, high-torque orbital motors and is designed for medium-duty mobile and industrial applications requiring reliable torque output and long service life.
Built on a disc-valve system with a three-zone design, the XL2 delivers smooth operation, high efficiency, and stable performance under varying loads. Precision-engineered bearings and optimized porting ensure consistent torque and extended durability in a compact design.
Each motor in the XL2 range features a SAE A 2-bolt mounting flange, G-thread ports, and a robust steel housing engineered to meet demanding system requirements.
Key Advantages
- High efficiency and torque stability at low speeds
- Three-zone disc-valve design for extended life and true bi-directionality
- Hydrodynamic bearings ensure smooth, reliable operation
- Compact and durable construction for medium-duty applications
- Optional cross-over relief or counterbalance valves for flexible system design
- Displacement range: 80 – 490 cm³/rev
- Continuous pressure: up to 205 bar
Intermittent pressure: up to 310 bar
Continuous torque: up to 845 Nm
Intermittent torque: up to 930 Nm
Speed capability: up to 900 rpm (depending on model)
Typical Applications
• Augers and screw conveyors
• Sweepers and snow blowers
• Conveyors and material-handling systems
• Agricultural and municipal equipment
• Compact drives and auxiliary hydraulic mechanisms
Technical Highlights
• Displacement range: 80 – 490 cm³/rev
• Flow capacity: up to 75 l/min continuous / 115 l/min intermittent
• Torque range: up to 845 Nm continuous / 930 Nm intermittent
• Operating temperature: –34 °C to +82 °C
• Recommended oil: Premium anti-wear hydraulic oil, viscosity ≥ 13 cSt at operating temperature
• Filtration: ISO 4406 class 20/18/13
• Ports: G ½ (pressure) / G ¼ (drain)
• Mounting flange: SAE A 2-bolt (Ø 82.5 mm pilot / Ø 106.4 mm bolt circle)
• Shaft options: Ø 32 mm cylindrical (code 16) or Ø 31.75 mm 14-tooth spline (code 99)
• Shaft seal: Standard pressure type (high-pressure optional)
• Maximum inlet pressure: 310 bar [4500 psi]
Note
Motors can run continuously at listed ratings; intermittent operation should not exceed 10 % of each minute.
For maximum service life, pre-run the motor at approximately 30 % of rated pressure for one hour before full-load operation.
Connecting a case drain line is recommended when operating at high pressures or temperatures to maintain low case pressure and extend seal life.
Obs: För att öppna 3D-filer krävs ett program som stöder filformatet
Copyright © 2025 HydraSpecma