XL2 100 No output Shaft 4-hole 106.4
Danfoss XL2 Series – High-Torque Orbital Motors with Disc Valve Design
The Danfoss XL2 series belongs to the Xcel™ family of low-speed, high-torque orbital motors and is designed for medium-duty mobile and industrial applications requiring reliable torque output and long service life.
Built on a disc-valve system with a three-zone design, the XL2 delivers smooth operation, high efficiency, and stable performance under varying loads. Precision-engineered bearings and optimized porting ensure consistent torque and extended durability in a compact design.
Each motor in the XL2 range features a SAE A 2-bolt mounting flange, G-thread ports, and a robust steel housing engineered to meet demanding system requirements.
Key Advantages
- High efficiency and torque stability at low speeds
- Three-zone disc-valve design for extended life and true bi-directionality
- Hydrodynamic bearings ensure smooth, reliable operation
- Compact and durable construction for medium-duty applications
- Optional cross-over relief or counterbalance valves for flexible system design
- Displacement range: 80 – 490 cm³/rev
- Continuous pressure: up to 205 bar Intermittent pressure: up to 310 bar
- Continuous torque: up to 845 Nm Intermittent torque: up to 930 Nm
- Speed capability: up to 900 rpm (depending on model)
Typical Applications
- Augers and screw conveyors
- Sweepers and snow blowers
- Conveyors and material-handling systems
- Agricultural and municipal equipment
- Compact drives and auxiliary hydraulic mechanisms
Technical Highlights
- Displacement range: 80 – 490 cm³/rev
- Flow capacity: up to 75 l/min continuous / 115 l/min intermittent
- Torque range: up to 845 Nm continuous / 930 Nm intermittent
- Operating temperature: –34 °C to +82 °C
- Recommended oil: Premium anti-wear hydraulic oil, viscosity ≥ 13 cSt at operating temperature
- Filtration: ISO 4406 class 20/18/13
- Ports: G ½ (pressure) / G ¼ (drain)
- Mounting flange: SAE A 2-bolt (Ø 82.5 mm pilot / Ø 106.4 mm bolt circle)
- Shaft options: Ø 32 mm cylindrical (code 16) or Ø 31.75 mm 14-tooth spline (code 99)
- Shaft seal: Standard pressure type (high-pressure optional)
- Maximum inlet pressure: 310 bar [4500 psi]
Note
Motors can run continuously at listed ratings; intermittent operation should not exceed 10 % of each minute.
For maximum service life, pre-run the motor at approximately 30 % of rated pressure for one hour before full-load operation.
Connecting a case drain line is recommended when operating at high pressures or temperatures to maintain low case pressure and extend seal life.
Partnumber:
631AG00025A
Package size:
0 pcs
Min. order quantity is:
1 pcs
Akseltype
Spline
Akseltætningstype
None
Antal montage huller
4
Arbejdsporte
G 1/2 BSP
Boltcirkel
125 mm
Dimension X
141.5 mm
Dimension XX
101.4 mm
Dimension Y
189 mm
Dimension YY
148.9 mm
Drænport
G 1/4 BSP
Filtreringskrav
ISO cleanliness code 4406:20/18/13
Flangens Styrediameter
199 mm
Fortrængning
100 cm3
Forureningsgrad maks.
20/18/13 - ISO 4406
Indgangstryk Maks.
310 bar
Integreret Kontraventil
No
Intermittent Flow Maks.
95
Intermittent Moment Maks.
445 Nm
Intermittent Rotationshastighed Maks.
924
Kontinuerligt Flow Maks.
75
Krav til drænledning
Recommended (Required under high case pressure)
Længde
189 mm
Maks. driftstemperatur
82 °C
Maks. moment på aksel
768 Nm
Maling
Black
Model kode
XL2
Moment kontinuerlig maks.
385 Nm
Monteringsflange
Bearingless 4-bolt flange (AZ)
Mærke navn
Danfoss
Olieviskositet anbefalet
20 - 75 cSt
Portkode
G3
Rotationshastighed kontinuerligt maks.
739 rpm
Temperatur maks.
+180 °C
Temperatur min.
-30 °C
Tryk intermitterende maks.
310 bar
Tryk kontinuerligt maks.
205 bar
Package size
0 pcs
Barcode
5704334983064
Gross weight
Kg
Net weight
Kg
Country of origin
CHN
Intrastat code
84122981
Danfoss XL2 Series – High-Torque Orbital Motors with Disc Valve Design
The Danfoss XL2 series belongs to the Xcel™ family of low-speed, high-torque orbital motors and is designed for medium-duty mobile and industrial applications requiring reliable torque output and long service life.
Built on a disc-valve system with a three-zone design, the XL2 delivers smooth operation, high efficiency, and stable performance under varying loads. Precision-engineered bearings and optimized porting ensure consistent torque and extended durability in a compact design.
Each motor in the XL2 range features a SAE A 2-bolt mounting flange, G-thread ports, and a robust steel housing engineered to meet demanding system requirements.
Key Advantages
- High efficiency and torque stability at low speeds
- Three-zone disc-valve design for extended life and true bi-directionality
- Hydrodynamic bearings ensure smooth, reliable operation
- Compact and durable construction for medium-duty applications
- Optional cross-over relief or counterbalance valves for flexible system design
- Displacement range: 80 – 490 cm³/rev
- Continuous pressure: up to 205 bar Intermittent pressure: up to 310 bar
- Continuous torque: up to 845 Nm Intermittent torque: up to 930 Nm
- Speed capability: up to 900 rpm (depending on model)
Typical Applications
- Augers and screw conveyors
- Sweepers and snow blowers
- Conveyors and material-handling systems
- Agricultural and municipal equipment
- Compact drives and auxiliary hydraulic mechanisms
Technical Highlights
- Displacement range: 80 – 490 cm³/rev
- Flow capacity: up to 75 l/min continuous / 115 l/min intermittent
- Torque range: up to 845 Nm continuous / 930 Nm intermittent
- Operating temperature: –34 °C to +82 °C
- Recommended oil: Premium anti-wear hydraulic oil, viscosity ≥ 13 cSt at operating temperature
- Filtration: ISO 4406 class 20/18/13
- Ports: G ½ (pressure) / G ¼ (drain)
- Mounting flange: SAE A 2-bolt (Ø 82.5 mm pilot / Ø 106.4 mm bolt circle)
- Shaft options: Ø 32 mm cylindrical (code 16) or Ø 31.75 mm 14-tooth spline (code 99)
- Shaft seal: Standard pressure type (high-pressure optional)
- Maximum inlet pressure: 310 bar [4500 psi]
Note
Motors can run continuously at listed ratings; intermittent operation should not exceed 10 % of each minute.
For maximum service life, pre-run the motor at approximately 30 % of rated pressure for one hour before full-load operation.
Connecting a case drain line is recommended when operating at high pressures or temperatures to maintain low case pressure and extend seal life.
Copyright © 2025 HydraSpecma